97 lines
3.1 KiB
Nix
97 lines
3.1 KiB
Nix
{
|
|
modulesPath,
|
|
config,
|
|
lib,
|
|
pkgs,
|
|
...
|
|
}:
|
|
|
|
{
|
|
#formatAttr = "sdImage";
|
|
|
|
#imports = [
|
|
# "${modulesPath}/installer/sd-card/sd-image.nix"
|
|
# "${modulesPath}/profiles/installation-device.nix"
|
|
#];
|
|
|
|
# sd-image-aarch64-installer/sd-image-raspberrypi-installer
|
|
#installer.cloneConfig = false;
|
|
|
|
# sd-image-raspberrypi
|
|
boot.consoleLogLevel = lib.mkDefault 7;
|
|
boot.kernelPackages = pkgs.linuxKernel.packages.linux_rpi4;
|
|
|
|
# The serial ports listed here are:
|
|
# - ttyS0: for Tegra (Jetson TX1)
|
|
# - ttyAMA0: for QEMU's -machine virt
|
|
boot.kernelParams = [
|
|
"console=ttyS0,115200n8"
|
|
"console=ttyAMA0,115200n8"
|
|
"console=tty0"
|
|
];
|
|
|
|
#sdImage = {
|
|
# populateFirmwareCommands =
|
|
# let
|
|
# configTxt = pkgs.writeText "config.txt" ''
|
|
# [pi3]
|
|
# kernel=u-boot-rpi3.bin
|
|
|
|
# [pi02]
|
|
# kernel=u-boot-rpi3.bin
|
|
|
|
# [pi4]
|
|
# kernel=u-boot-rpi4.bin
|
|
# enable_gic=1
|
|
# armstub=armstub8-gic.bin
|
|
#
|
|
# # Otherwise the resolution will be weird in most cases, compared to
|
|
# # what the pi3 firmware does by default.
|
|
# disable_overscan=1
|
|
#
|
|
# # Supported in newer board revisions
|
|
# arm_boost=1
|
|
#
|
|
# [cm4]
|
|
# # Enable host mode on the 2711 built-in XHCI USB controller.
|
|
# # This line should be removed if the legacy DWC2 controller is required
|
|
# # (e.g. for USB device mode) or if USB support is not required.
|
|
# otg_mode=1
|
|
#
|
|
# [all]
|
|
# # Boot in 64-bit mode.
|
|
# arm_64bit=1
|
|
#
|
|
# # U-Boot needs this to work, regardless of whether UART is actually used or not.
|
|
# # Look in arch/arm/mach-bcm283x/Kconfig in the U-Boot tree to see if this is still
|
|
# # a requirement in the future.
|
|
# enable_uart=1
|
|
#
|
|
# # Prevent the firmware from smashing the framebuffer setup done by the mainline kernel
|
|
# # when attempting to show low-voltage or overtemperature warnings.
|
|
# avoid_warnings=1
|
|
# '';
|
|
# in
|
|
# ''
|
|
# (cd ${pkgs.raspberrypifw}/share/raspberrypi/boot && cp bootcode.bin fixup*.dat start*.elf $NIX_BUILD_TOP/firmware/)
|
|
|
|
# # Add the config
|
|
# cp ${configTxt} firmware/config.txt
|
|
|
|
# # Add pi3 specific files
|
|
# cp ${pkgs.ubootRaspberryPi3_64bit}/u-boot.bin firmware/u-boot-rpi3.bin
|
|
|
|
# # Add pi4 specific files
|
|
# cp ${pkgs.ubootRaspberryPi4_64bit}/u-boot.bin firmware/u-boot-rpi4.bin
|
|
# cp ${pkgs.raspberrypi-armstubs}/armstub8-gic.bin firmware/armstub8-gic.bin
|
|
# cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-4-b.dtb firmware/
|
|
# cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-400.dtb firmware/
|
|
# cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-cm4.dtb firmware/
|
|
# cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-cm4s.dtb firmware/
|
|
# '';
|
|
# populateRootCommands = ''
|
|
# mkdir -p ./files/boot
|
|
# ${config.boot.loader.generic-extlinux-compatible.populateCmd} -c ${config.system.build.toplevel} -d ./files/boot
|
|
# '';
|
|
#};
|
|
}
|