{
  modulesPath,
  config,
  lib,
  pkgs,
  ...
}:

{
  #formatAttr = "sdImage";

  #imports = [
  #  "${modulesPath}/installer/sd-card/sd-image.nix"
  #  "${modulesPath}/profiles/installation-device.nix"
  #];

  # sd-image-aarch64-installer/sd-image-raspberrypi-installer
  #installer.cloneConfig = false;

  # sd-image-raspberrypi
  boot.consoleLogLevel = lib.mkDefault 7;
  boot.kernelPackages = pkgs.linuxKernel.packages.linux_rpi4;

  # The serial ports listed here are:
  # - ttyS0: for Tegra (Jetson TX1)
  # - ttyAMA0: for QEMU's -machine virt
  boot.kernelParams = [
    "console=ttyS0,115200n8"
    "console=ttyAMA0,115200n8"
    "console=tty0"
  ];

  #sdImage = {
  #  populateFirmwareCommands =
  #    let
  #      configTxt = pkgs.writeText "config.txt" ''
  #        [pi3]
  #        kernel=u-boot-rpi3.bin

  #        [pi02]
  #        kernel=u-boot-rpi3.bin

  #        [pi4]
  #        kernel=u-boot-rpi4.bin
  #        enable_gic=1
  #        armstub=armstub8-gic.bin
  #
  #        # Otherwise the resolution will be weird in most cases, compared to
  #        # what the pi3 firmware does by default.
  #        disable_overscan=1
  #
  #        # Supported in newer board revisions
  #        arm_boost=1
  #
  #        [cm4]
  #        # Enable host mode on the 2711 built-in XHCI USB controller.
  #        # This line should be removed if the legacy DWC2 controller is required
  #        # (e.g. for USB device mode) or if USB support is not required.
  #        otg_mode=1
  #
  #        [all]
  #        # Boot in 64-bit mode.
  #        arm_64bit=1
  #
  #        # U-Boot needs this to work, regardless of whether UART is actually used or not.
  #        # Look in arch/arm/mach-bcm283x/Kconfig in the U-Boot tree to see if this is still
  #        # a requirement in the future.
  #        enable_uart=1
  #
  #        # Prevent the firmware from smashing the framebuffer setup done by the mainline kernel
  #        # when attempting to show low-voltage or overtemperature warnings.
  #        avoid_warnings=1
  #      '';
  #    in
  #    ''
  #      (cd ${pkgs.raspberrypifw}/share/raspberrypi/boot && cp bootcode.bin fixup*.dat start*.elf $NIX_BUILD_TOP/firmware/)

  #      # Add the config
  #      cp ${configTxt} firmware/config.txt

  #      # Add pi3 specific files
  #      cp ${pkgs.ubootRaspberryPi3_64bit}/u-boot.bin firmware/u-boot-rpi3.bin

  #      # Add pi4 specific files
  #      cp ${pkgs.ubootRaspberryPi4_64bit}/u-boot.bin firmware/u-boot-rpi4.bin
  #      cp ${pkgs.raspberrypi-armstubs}/armstub8-gic.bin firmware/armstub8-gic.bin
  #      cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-4-b.dtb firmware/
  #      cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-400.dtb firmware/
  #      cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-cm4.dtb firmware/
  #      cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-cm4s.dtb firmware/
  #    '';
  #  populateRootCommands = ''
  #    mkdir -p ./files/boot
  #    ${config.boot.loader.generic-extlinux-compatible.populateCmd} -c ${config.system.build.toplevel} -d ./files/boot
  #  '';
  #};
}